I don’t have much on this one. I did see it at the Consumer Electronics Show in Las Vegas this year. I got some unadvertised extras while playing with the display prototype unit.
We weren’t sure this one was going to be available. They are in the States, and I’ve included the HOT SHEET below.
Model 79-290 AM-USB/LSB-Weather
Transceiver with Detachable Control Panel. There Isn’t Anything This Midland Radio Can’t Do!
120-channel operation (40 AM, 40 USB/40 LSB) and monitoring of N.O.A.A. and Canadian weather channels is impressive enough. But that’s only the beginning of the 79-290 story.
There are also performance features like a Dual Watch, four memory channels, and full-stage noise blanking. And there’s still more:
- Size: 2″H x 61/4″W x 7″D (48 x 159 x 178mm)
- Receiver Sensitivity:AM: 0.8 uV @ 10 dB S/N SSB: 0.5 uV @ 20 dB S/N WX: 1.0 uV @ 20 dB S/N
- Receiver Selectivity: -6 dB @ 2.5 kHz, -60 dB @ 10 kHz
- Output Power: 12 Watts SSB, 4 Watts AM
- Frequency Control: PLL
- Controls: On/Off/Volume, Variable squelch, Weather/CB selector, Last channel recall. LOC/DIS, Mic Gain, Four CB channel memory buttons, Dual Watch, Frequency/channel selector, FrequencyFine/coarse adjustment, Channel 9 memory, WX/CB channel selector, Detach release. CB band (AM/USB/LSB) selector
- Power Requirements: 13.8V, DC. negative ground
- Accessories Included: Full-size microphone w/4-pin screw-on connector DC power cord, Mounting bracket and hardware, User’s manual.
|Detachable control panel||For added security. Battery powered to retain data for up to 100 hours|
|Multi-function black matrix LCD display||Indicators for channel/frequency (1/8″ high), 12-segment RFoutput/signal meter. memory channels 1-4. noise blanker, dual watch,RF gain, weather and operating mode|
|Channel Number- or ‘Frequency (MHz)’ readout||You have the choice Built-in I 0-channel weather receiver for the USAand CanadaKeeps you up-to4he-minute on local conditions|
|Four memory channels||Instant access to any of four user-selectable channels|
|Mic gain||Boosts TX output|
|Dual watch||Monitoring of any two user-selectable channels|
|Coarse/fine tuning for USB/LSB||Quick, accurate frequency tuning|
|Full-Stage noise blanking system||To reduce static and engine pulse to a whisper|
|Local-DX receiver switch||Reduces receiver gain for close stations|
|High performance CPU||For pinpoint channel selection and self-adjusting frequency operation|
|Jacks for external speaker and antenna||Added flexibility|
Features and specifications are subject to change without notice.
Review of Midland 79-290 SSB Mobile
The Midland 79-290 is the smallest sideband mobile available today. It measures only 2″ high by 6.25″ wide by 7″ deep. The small size combined with the detachable face makes it possible to safely mount it permanently in many vehicles.
This is a new generation of CB radio designed and manufactured in Korea. Instead of producing a convertible 10-meter amateur, they have used the reverse philosophy. Producing a convertible FCC-approved CB. Maybe the industry is trying to keep ahead of Uncle Charlie.
It could just be a matter of time before Uncle Charlie wakes up and realizes that the 10-meter loophole is being stretched beyond its limits with the Connex, SuperStar, and Galaxy-type 10-meter-only units.
It’s obvious that they are DX radios with their band switches disabled. The Midland has some unique features for a legal SSB CB unit. It has dual watch capability.
This option gives the operator the ability to select and monitor a second channel during normal operations. Also, four programmable memory channels can be selected at the push of a button or scanned for activity if desired.
The LCR button stands for the last channel recall and returns the unit to the previous channel when depressed. This allows quick jumping between two channels. In addition, fine and coarse clarifiers are provided for easy tuning while on the move.
Opening the unit and at a quick glance, you realize that this isn’t a copy of an earlier product. The only similarity between this radio and any other unit is in the transmitter’s final output. The final output stage uses two 2SC1969 transistors instead of the traditional single transistor.
This is the same configuration used in the export and most 10-meter radios that have 30-40-watt PEP output. The only difference is they employ the 2SC2312 transistors in the final stage.
Three variable resistors are used to adjust the AM and SSB output of the transmitter. VR8 is the SSB ALC control, VR3 is the AM power adjustment, and there is a VR for adjusting the AM modulation. What’s missing is the driver and final bias adjustments.
I find that these adjustments are important in getting the cleanest signal on the sideband. But I know that most factories don’t do a fine adjustment on these controls anyway.
This Midland unit is tuned up to 28 watts PEP and 8-watt dead key swinging up to 25 watts on AM. The audio on sideband had a slight warble that I was unable to correct with the normal schemes I’ve used in the past.
The audio was clean on AM, and when the sideband output was reduced to 12 watts PEP. The stock mic supplied is adequate but nothing special. A good-quality mic would improve the tone quality but wouldn’t improve the warble.
A warble is usually caused by poor voltage regulation at the PLL/VCO or in the clarifier circuit. As the output was turned up, I noticed the display lamps dimmed excessively, possibly indicating a poor path for the 13.8 voltage supply. This could be the reason for the warbling transmission.
Frequency modifications are enabled by changing solder shorts on the PC board in the detachable face and are user-selectable by way of the front panel.
The five-digit frequency display comes in handy once the expansion is made. No road map is needed here. Once the deed is done, there are three options to choose from. The normal default is straight forty channels.
The second option is expanded coverage of 240 channels from 25.615 MHz to 28.305 MHz.
The third option is 10-meter coverage from 28.000 MHz to 29.700 MHz by 10 KHz steps totaling 170 channels.
To switch from 40 to 240 channels, depress both the “DW”‘ and “9” buttons simultaneously while turning the power on. At first, a “D” symbol will appear on the LCD display. Bands “A”‘ through “F” can be selected by depressing the “19” button.
To return to the regular 40 channel mode just repeat the steps above. To switch from 40 channels to 10-meter coverage, depress both the “LCR” and “Mic” buttons simultaneously while turning the power on. 28.000 MHz will be displayed on the LCD display.
As before, to return to 40 channels, repeat the steps above. It’s not possible to switch directly from 240 channel mode to the 10 Meter mode or visa versa. The expanded modes can only be accessed from the 40-channel mode.
This front panel selection of expansion is great if you don’t want Uncle Charlie to catch you with extras or unauthorized out-of-band or ham band use. Memory back-up is achieved with a rechargeable battery in the detachable face of the unit.
Power must be applied to the radio for 120 hours to fully charge the battery. A fully charged battery will hold the memory for 240 hours. Also, the face or control head must be removed from the radio to achieve 240-hour memory backup.
If memory power is lost, the radio returns to the default 40-channel mode. The S meter looked flashy, but after close inspection, I realized the segments jumped by two for readings above S9. I don’t understand why they provided all the bars in the meter if they weren’t going to make proper use of them. ‘Me meter reacted the same in the RF mode, too. Unfortunately, the receiver was the biggest disappointment in the radio.
When attached to a base antenna, I was almost unable to determine what channel some operators were on because they were bleeding over all forty channels. I could understand every word. The only way I could tell the channel they were on was when their audio sounded clear.
I’ve never encountered this level of splatter in any radio before. When checking the offending signals with a Tram D201, I found their signals to be between 10 and 20 dB, and they were hardly noticeable on the adjacent channels.
I also did some research and found that I wasn’t the first to experience this problem with the 79-290. Although the problem would be less severe in mobile operation, it would still be difficult to communicate with the low-level signals splashing the receiver. It would be frustrating on interstate highways or in areas heavily populated with CBers.
I’ve heard stories of drivers throwing radios out the window for less. In summary, I must say I’m impressed with the features and size of the radio. It has real potential to be a big player in the CB market. For that to happen, they need to address some problems.
I think the battery life is inadequate. Six days of backup isn’t really enough, especially when the battery charge rate is so slow. It takes three days of uninterrupted 12-volt supply to the radio to fully charge the battery.
Second all the segments of the meter display should be driven separately for proper resolution. Third, the sideband warble must be resolved. Finally, the receiver must be improved or redesigned, and the radio isn’t useable in its present condition.
One other feature that I’d like to see is 5 KHz steps in the expanded modes. I hope Midland bites the bullet and corrects the problems, and I know I could sell many of these radios, especially if the HR2510s are really history.